ADT7476
Enhance Acoustics Register 1 (0x62)
Bit 7 (MIN3) = 0, PWM3 is off (0% PWM duty cycle) when
temperature is below T MIN ? T HYST .
Bit 7 (MIN3) = 1, PWM3 runs at PWM3 minimum duty cycle
below T MIN ? T HYST .
Bit 6 (MIN2) = 0, PWM2 is off (0% PWM duty cycle) when
temperature is below T MIN ? T HYST .
Bit 6 (MIN2) = 1, PWM2 runs at PWM2 minimum duty cycle
below T MIN ? T HYST .
Bit 5 (MIN1) = 0, PWM1 is off (0% PWM duty cycle) when
temperature is below T MIN ? T HYST .
Bit 5 (MIN1) = 1, PWM1 runs at PWM1 minimum duty cycle
below T MIN ? T HYST .
Configuration Register 6 (0x10)
[0] SLOW = 1, slows the ramp rate for PWM changes
associated with the Remote 1 temperature channel by a factor
of 4.
[1] SLOW = 1, slows the ramp rate for PWM changes
associated with the local temperature channel by a factor of 4.
[2] SLOW = 1, slows the ramp rate for PWM changes
associated with the Remote 2 temperature channel by a factor
of 4.
[7] ExtraSlow = 1, slows the ramp rate for all fans by a factor
of 39.2%.
The following sections list the ramp-up times when
enhanced acoustics is enabled for each temperature channel.
Enhance Acoustics Register 1 (0x62)
[2:0] ACOU selects the ramp rate for PWM outputs
associated with the Remote Temperature 1 input.
000 = 37.5 sec
001 = 18.8 sec
010 = 12.5 sec
011 = 7.5 sec
100 = 4.7 sec
101 = 3.1 sec
110 = 1.6 sec
111 = 0.8 sec
Enhance Acoustics Register 2 (0x63)
[2:0] ACOU3 selects the ramp rate for PWM outputs
associated with the local temperature channel.
000 = 37.5 sec
001 = 18.8 sec
010 = 12.5 sec
011 = 7.5 sec
100 = 4.7 sec
101 = 3.1 sec
110 = 1.6 sec
111 = 0.8 sec
[6:4] ACOU2 selects the ramp rate for PWM outputs
associated with the Remote Temperature 2 input.
000 = 37.5 sec
001 = 18.8 sec
010 = 12.5 sec
011 = 7.5 sec
100 = 4.7 sec
101 = 3.1 sec
110 = 1.6 sec
111 = 0.8 sec
When Bit 7 of Configuration Register 6 (0x10) = 1, the
above ramp rates change to the values below.
000 = 52.2 sec
001 = 26.1 sec
010 = 17.4 sec
011 = 10.4 sec
100 = 6.5 sec
101 = 4.4 sec
110 = 2.2 sec
111 = 1.1 sec
Setting the appropriate slow bit [2:0] of Configuration
Register 6 (0x10) slows the ramp rate further by a factor of 4.
Fan Presence Detect
This feature is used to determine if a 4-wire fan is directly
connected to a PWM output. This feature does not work for
3-wire fans. To detect whether a 4-wire fan is connected
directly to a PWM output, the following must be performed
in this order:
1. Drive the appropriate PWM outputs to 100%
duty cycle.
2. Set Bit 0 of Configuration Register 2 (0x73).
3. Wait 5 ms.
4. Program fans to run at a different speed if necessary.
5. Read the state of Bits [3:1] of Configuration
Register 2 (0x73). The state of these bits reflects
whether a 4-wire fan is directly connected to the
PWM output.
As the detection time only takes 5 ms, programming the
PWM outputs to 100% and then back to its normal speed is
not noticeable in most cases.
How Fan Presence Detect Works
4-wire fans typically have an internal pull up to 4.75 V
± 10%, which typically sources 5 mA. While the detection
cycle is on, an internal current sink is turned on, which sinks
current from the fan’s internal pullup. By driving some of the
current from the fan’s internal pullup (~100 m A) the logic
buffer switches to a defined logic state. If this state is high,
a fan is present; if the state is low, no fan is present.
Note: The PWM input voltage should be clamped to 3.3 V.
This ensures the PWM output is not pulled to a voltage
higher than the maximum allowable voltage on that pin
(5.5 V).
http://onsemi.com
44
相关PDF资料
ADT7490ZEVB BOARD EVALUATION FOR ADT7490
ADZS-21262-1-EZEXT BOARD DAUGHTER FOR ADSP-21262
ADZS-BF-EZEXT-1 BOARD DAUGHTER ADSP-BF533/561KIT
ADZS-BFAV-EZEXT BOARD DAUGHT ADSP-BF533,37,61KIT
ADZS-BFSHUSB-EZEXT BOARD DAUGHTER EZ EXTENDER
ADZS-BRKOUT-EX3 ADZS-BRKOUT-EX3
ADZS-SHAUDIO-EZEXT SHARC AUDIO EZ-EXTENDER
ADZS-WVGALCD-EX3 BOARD EXTENDER WVGA/LCD EI3
相关代理商/技术参数
ADT7481 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm
ADT7481ARMZ 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-001 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-1 功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统(传感器) 传感器类型:内部和外部 感应温度:-40°C ~ 125°C,外部传感器 精确度:±2.5°C 本地(最大值),±5°C 远程(最大值) 拓扑:ADC,比较器,寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7481ARMZ-1R7 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-1REEL 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADT7481ARMZ-1REEL7 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm
ADT7481ARMZ-1RL 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor